川北某黑色页岩型铼矿工艺矿物学研究

通过矿相显微镜、扫描电镜、电子探针、X射线能谱元素面分析等多种手段综合研究了川北某黑色页岩型铼矿中铼的赋存状态。样品为黑色页岩,有机碳含量较高。粘土矿物总量为14.6%,黄铁矿含量16.2%,石英含量37.7%。样品具典型的粘土结构,矿物粒度微细。铼有两种赋存状态,一种呈类质同象形式赋存于黄铁矿内,另一种则以分散形式存在。典型黄铁矿测点Re平均含量为0.024%。黄铁矿是Re的重要载体矿物。建议通过浮选分离黄铁矿,从而实现Re的富集。      

浅析混凝土搅拌站的防雷

近年来,我市因雷击而导致搅拌站系统瘫痪停产、影响工程进度的事件时有发生,在针对混凝土搅拌站配料秤的实际检定工作中,也常发现配料秤的称重传感器因雷击损坏而影响计量准确性。因此,对混凝土搅拌站防雷的研究具有重要意义。本文阐述了雷电对混凝土搅拌站的主要危害,分析了混凝土搅拌站常见的雷击原因及其防护措施,旨在引起生产方、安装方以及使用方对混凝土搅拌站防雷的共同重视。     

Effect of strain rate on the dynamic compressive mechanical behaviors of rock material subjected to high temperatures

Strain rate is not only an important measure to characterize the deformation property, but also an important parameter to analyze the dynamic mechanical properties of rock materials. In this paper, by using the SHPB test system improved with high temperature device, the dynamic compressive tests of sandstone at seven temperatures in the range of room temperature to 1000 °C and five impact velocities in the range of 11.0–15.0 m/s were conducted. Investigations were carried out on the influences of strain rate on dynamic compressive mechanical behaviors of sandstone. The results of the study indicate that the enhancement effects of strain rates on dynamic compressive strength, peak strain, energy absorption ratio of sandstone under high temperatures still exist. However, the increase ratios of dynamic compressive strength, peak strain, and energy absorption ratio of rock under high temperature compared to room temperature have no obvious strain rate effects. The temperatures at which the strain rates affect dynamic compressive strength and peak strain most, are 800, and 1000 °C, respectively. The temperatures at which the strain rates affect dynamic compressive strength and peak strain weakest, are 1000 °C, and room temperature, respectively. At 200 and 800 °C, the strain rate effect on energy absorption ratio are most significant, while at 1000 °C, it is weakest. There are no obvious strain rate effects on elastic modulus and increase ratio of elastic modulus under high temperatures. According to test results, the relationship formula of strain rate with high temperature and impact load was derived by internalizing fitting parameters. Compared with the strain rate effect at room temperature condition, essential differences have occurred in the strain rate effect of rock material under the influence of high temperature.     

磷酸高效分解磷矿实验研究

为改进湿法磷酸生产工艺,提高副产石膏的品质,减少湿法磷酸固体副产物磷石膏堆存产生的经济和环保压力,进行了磷酸分解磷矿制磷酸的实验研究。采用贵州某磷矿为主要原料,研究了湿法磷酸预分解磷矿的反应条件。通过单因素实验确定了湿法磷酸分解磷矿最优反应条件：反应温度为75 ℃,磷酸与磷矿的质量比（液固比）为9,反应时间为3 h,磷酸质量分数为30%（以五氧化二磷计）。在此条件下,磷矿的分解率为98.62%。     

Control of the particle microstructure during the synthesis of bulk-polymerized transparent methacrylate-acrylonitrile-butadiene-styrene resin

A series of methacrylate-acrylonitrile-butadiene-styrene (MABS) resins was prepared using bulk polymerization. The polarity of the continuous phase and the compatibility of two phases were changed by adjusting the methyl methacrylate (MMA) content, choosing values that were close to styrene-butadiene rubber solubility value. The possibility of controlling the microstructure of the MABS resin by changing the polarity of the components and the compatibility of two phases was assessed. The dynamic mechanical analysis shows that the compatibility of two phases varies with the MMA content. The morphological analysis shows that increasing MMA contents results in a gradual decrease in the sub-inclusion structure with a network skeleton of rubber particles, and that all the particles become solid rubber when the MMA content reaches 75%. The sub-inclusion structure reappears but does not have a network skeleton when the MMA content is 90%. The impact strength and morphological analysis indicate that the solid rubber particles and the sub-inclusion structure with a network skeleton provide excellent toughness, while the sub-inclusion structure without a network skeleton does not. In contrast, the transmittance of the ABS resin first increased and then decreased with increasing MMA content.     

内热型超声雾化溶液再生系统最优内热量的研究

基于质量守恒、能量守恒定律，建立了内热型超声雾化溶液再生系统（IH-UARS）的再生性能预测模型并进行了充分的实验验证，通过研究不同内热量下IH-UARS的再生性能及其变化规律，寻求系统所需的最佳内热量并明确其可能的影响因素。结果表明：IH-UARS系统存在最优的内热量范围，使其再生系统性能最佳；所需最优内热量随着再生溶液流量增大呈显著的对数增长，但受空气流量的影响较弱；在该研究中的标准工况下，IH-UARS所需最优内热量约为275~350 W。此外研究发现：内热量的增长有益于促进初始浓度较高的溶液进一步浓缩再生，如当IH-UARS中内热量增至800 W时，其初始浓度为36%的溶液比24%的溶液浓度增量指标改善幅度高37%。研究所得结果可对提高溶液再生性能及经济性提供积极参考。     

钒掺杂二氧化钛光催化活性研究

二氧化钛凭借优异的光催化性能,越来越受到人们的广泛关注和重视。以钛酸四丁酯为原料,利用水解-水热-干燥/煅烧工艺制备得到未掺杂TiO₂光催化剂和掺钒TiO₂光催化剂,利用其对甲基橙溶液的降解率做了比较分析。结果表明,以钛酸四丁酯为原料,采用溶胶-凝胶法制备钒掺杂TiO₂光催化剂是可行的。制备V/TiO₂产品的最佳工艺条件：钒钛质量比为6∶100、水热温度为160 ℃、水热时间为12 h,120 ℃下干燥14 h。紫外光照射条件下,甲基橙光催化降解效率达到99.10%,降解时间小于45 min。     

南水北调中线工程受水区二期需调水量预测研究

2002年12月国务院批复了《南水北调工程总体规划》，明确中线工程分两期建设。目前，一期工程已经通水。近年来，随着社会经济的快速发展，受水区的人口、生产规模、节水水平、人们对环境的要求都发生了变化，因此有必要根据新的情况对受水区的用水需求重新预测。分析了城市化发展和城镇用水变化的新形势，依据流域、区域水资源规划成果，提出了中线二期工程受水区需调水量，并与《南水北调中线工程规划》提出的二期需调水量进行对比，以供各方参考。     

基于WiMAX通信网络的电源监控系统的构建

分析了全球微波接入互存(WiMAX)的技术特点和算法复杂度,探讨了其在电源监控系统中的应用,提出了基于Inter WiMAX Connection 2250技术的远程电源监控系统。在讨论WiMAX物理层算法的基础上,确定了以正交频分多址(OFDMA)模式为主体的物理层通信协议,提高了信道的利用率,抑制了码间干扰,为构建电源监控系统打下了良好的基础。     

Sensor network design based on system-wide reliability criteria. Part I: Objectives

Reliability based criteria are quite popular for optimal sensor network design. We present a modified definition of system reliability for sensor network design for two applications: reliable estimation of variables in a steady state linear flow process, and reliable fault detection and diagnosis for any process. Unlike the weakest-link based definition of system reliability in the literature, the proposed definition considers the entire system and is consistent with the reliability concept used in classical reliability literature. For each application, dual approaches for defining system reliability are proposed, and their analogy with the reliability problem in the classical reliability literature is established. Using examples and stochastic simulations, the advantage of using the proposed system reliability in contrast to the existing definition is illustrated. Part II of this series of articles presents methods for efficient generation of the system reliability function and its use in optimization-based approaches for designing optimal sensor networks.